555 in. Polished intake Jessel belt drive Holly dominator CSI water pump MSD distributor and plug wires crank trigger and wheel went 6:30s in 3550 Pound car with Driver. Whiteland, IN 46184 (317) 445-3183
GM Bare LQ4 Engine Block, Ready to build-Hot tanked-Bored honed w deck plates to 4.030-9.222 Deck Height-Surfaced squared deck surfaces$900GM Chevrolet Camaro Corvette Trailblazer SS LS1 LS2 LS3 LS7 LM7 LR4 5.3 4.8 LSX 6.2 6.0 L33 LC9 LH9 LMF or a LMG
I have a good pair of headers that came off of a 70 Chevelle with a 454 BBC. I understand that they will fit a 1968 thru 72 Chevelle and they may also fit others. Calls only to Joe at 317-989-eight two two five, Please no texts or emails.Corvette vette nova Malibu c10 c 10 20 30 50 60 K rat hot rod impala caprice
I have a flathead Ford block that I just got out of the machine shop. It was baked and blasted then magnifluxed and checked out good. Standard bore. it is an 8 BA, CM. 1948-53. Please look at the photos before you call me. Calls only to Joe at 317-989-eight 2 two five. Please no texts or emails. flat head rat hot rod rt 59 ab 239 255
1970 Ford 429 SCJ short block. I think I have parts all parts to complete, except exhaust manifolds and valve covers. The heads are not correct, have c-9 castings. I traded for engine a few years ago and decided I am not going to use. I can not give a lot of information on engine, but will tell what I was told. $1850 CALL NO TEXT NO EMAIL
1-1965 396 block,codeLF,hot tanked,magged,ok,standard bore 2-bolt main,some extra parts,1-1971 402 block,codeCLB,hot tanked magged ok,standard bore 2 bolt main,some extra parts,will seperate,heads and misc parts available. indianapolis, IN 46239 (317) 694-2963
fully remanufactured chevy engine ready to install call for info and options - additional charge $300 core charge $300 shipping if you dont have a core and need it shipped
Fresh 60 over 4 bolt main 350. One piece rear main roller motor. New Eagle crank rods. Speedpro hyperutectic pistons. ARP main studs. Cloyes timing set. Melling M55HV pump. GM ZZ4 roller cam kit. Vortec 906 heads. 2.021.60 stainless valves. Screw in studs guide plates. Roller rockers. Edelbrock dual quad intake carbs. MSD ignition system. Electric water pump. Every part is new but the block and...
Mopar small block 727 transmission. I think its a 1969 date. It will need to be rebuilt since I am not sure when the last time it was used. Long shaft 727 for a 2wd car. Price firm.CASH IN PERSON.Mopar, Charger, Cuda, Challender, Duster, Dart, Demon, Roadrunner. 340, 360, Plymouth Dodge
Mopar Small block Micky Thompson Aluminum valve covers. Very good condition. Will fit 273, 318, 340 and 360.Mopar, 440, hemi, Roadrunner, Charger, Dart, Duster, Demon, Cuda, Challenger
fully remanufactured chevy engine ready to install call for info and options - additional charge $300 core charge $300 shipping if you dont have a core and need it shipped
2 ford aluminium block 1 10.300 4.44 bore 55MM roller cam bearings/water block #2 11.20 aluminium ford block steel main caps steel upper bearings 60MM cam/4.621 cly bore have cranks cams belt drive lifters 317-371-0378. indianapolis, IN 46222 (317) 371-0378
custom made headers out of a 2002 trans am with the front frame still in. Stainless v bands Stainless bullhorns 5 inch exit 2 1/4-2.5 Very nice set would look brand new if they were ceramic coated but they do have new high temp paint on them. These came out of a stock style front suspension 4th gen f body However I feel like these would fit most chassis cars with little to no modification. WEST...
This is a brand new Bob Book 414 small block Chevy comp motor with dyno time only. It has a dry sump with a 5 stage oil pump, Dart 4.500 bore spacing block, Winberg crank, MGP rods, JE pistons, Slawco billet heads, HRE manifold and 2 x 4 barrel Dominators. It made 1200HP on the dyno. It is a complete motor from carbs to pan and was built with the best possible parts!!! No shortcuts anywhere!!! ...
We have several NEW GM ROX 4.500" bore center bare blocks and cylinder heads castings for the small block Chevrolet platform available for purchase. All blocks and head castings are NOS GM components. The 4.500" bore center platform (standard SBC is 4.400" bore center) will allow the user to machine the blocks up to 4.250" bore while maintaining a minimum wall thickness of .225" on the thrust s...
825 cid 1800+ HP LSM Billet Block, AJPE 10 Degree DRCE Heads, Titanium Valves, Pac & Psi Valve Springs, Wenberg Billet Crank, Crower Titanium Rods, Titanium Coated Pins, CP Pistons, LSM 65mm Cam, Jesel Belt Drive, HRE Intake, Jesel Keyed .937 Lifters, Manton 9/16 .200 Pushrods, AJPE 2.0 Shaft Rockers, Bob Book Split Carbs, Autoverdi Dry Sump, Star Max Vacuum Pump System, Moroso Oil Pan, Oil Tan...
over a month agoAvon, IN+16 milesAuto Parts for Sale814-872-3048
Condition: New Brand: CUSTOM MADE Manufacturer Part Number: SB&BBC UPC: Does not apply BLOCK MOUNTING VACUUM PUMP BRACKET FOR ................ MOUNTING VACUUM PUMP BRKT TO BLOCK FITS ............... BB & SB CHEVROLET BLOCKS WORKS WITH MOROSO AND MOST OTHER VACUUM PUMPS. WHEN THE VACUUM PUMP MOUNTING BRKT CAN NOT BE SECURED TO THE CYL HDS, OR,THERE IS NOT AN ENGINE PLATE TO MOUNT VACUUM PUMP BRA...
Condition: New Brand: Powermadd MPN: 45527 Manufacturer Part Number: 45527 ATV DIRT BIKE MARINE SNOWMOBILE STREET TRAILER UTV POWERMADD Powermadd 45527 Powermadd Pivot Style Riser Block - Arctic Cat/yamaha - 4' For Additional Product Details or Technical Questions Please Call 1-800-983-2210 Monday-Friday 9AM to 6PM Eastern Time Manufacturer Part Number: 45527 Lionparts #: 45527-POWERMADD 30 Day...
Condition: New Brand: Powermadd MPN: 45528 Manufacturer Part Number: 45528 ATV DIRT BIKE MARINE SNOWMOBILE STREET TRAILER UTV POWERMADD Powermadd 45528 Powermadd Pivot Style Riser Block - Polaris - 4' For Additional Product Details or Technical Questions Please Call 1-800-983-2210 Monday-Friday 9AM to 6PM Eastern Time Manufacturer Part Number: 45528 Lionparts #: 45528-POWERMADD 30 Day Hassle-Fr...